E375_B ELMER'S GLUE-ALL
Material Safety Data Sheet



1. Chemical Product and Company Identification

     DESCRIPTION:     ELMER'S GLUE-ALL

     PRODUCT TYPE:    PVAC BASED ADHESIVE

     APPLICATION:     FOR PRODUCT CODES SEE SECTION 16



	* Manufacturer/Supplier Information

     MSDS Prepared by:

     Elmer's Products, Inc.                           Emergency Phone Number

     1000 Kingsmill Parkway                          Poison Control Center

     Columbus, OH  43229                             1-800-228-5635 ext 22

     For additional health, safety or regulatory information, call 614-225-7689.

     Call 1-800-848-9400 to place an order or request additional MSDSs.



2. Composition, Information on Ingredients

     No hazardous ingredients known to Borden.



3. Hazards Identification



3.1 Emergency Overview

     Appearance                          Milky white liquid

     Odor                                Mild acetic aroma

     Not an immediate health hazard.

     Not a significant fire hazard.



	* HMIS Rating

           HEALTH = 0 (minimal)

     FLAMMABILITY = 0 (minimal)

       REACTIVITY = 0 (minimal)



3.2 Potential Health Effects



	* Immediate Hazards

     INGESTION:   No hazards known to Borden.

     INHALATION:  No hazards known to Borden.

     SKIN:        No hazards known to Borden.

     EYES:        No hazards known to Borden.



	* Delayed Hazards

     None of the components present in this product at concentrations equal

     to or greater than 0.1% have been listed by NTP, classified by IARC,

     nor regulated by OSHA as a carcinogen.



4. First Aid Measures

     INGESTION:   If accidently swallowed, dilute by drinking large

                  quantities of water.  Immediately contact poison control

                  center or hospital emergency room for any other

                  additional treatment directions.

     EYES:        Immediately flush eyes with plenty of water.  Call a

                  physician if irritation persists.



5. Fire Fighting Measures

     Autoignition Temperature            Not available

     Upper/Lower Flammable Limits        Not applicable

     Up/Lower Explosive Limits, % by Vol Not applicable

     Flash Point                         Not applicable

     Will not burn unless water has evaporated.  Dried material may

     burn.

     In case of fire, water should be used to keep fire-exposed

     containers cool.



6. Accidental Release Measures

     Soak up with absorbent material and remove to a chemical disposal

     area.  Prevent entry into natural bodies of water.



7. Handling and Storage



7.1 Handling

     Handle in accordance with good industrial hygiene and safety

     practices.



7.2 Storage

     Keep from freezing.

     Store in a cool, dry place.

     Keep containers tightly closed.



8. Exposure Controls/Personal Protection



8.1 Exposure Controls

     No special control measures necessary under normal conditions of use.



8.2 Personal Protection

     No special protection necessary.



8.3 Exposure Guidelines

     None established



9. Physical and Chemical Properties

     Percent Volatiles                   58

     pH @ 25 C                           4.7

     Specific Gravity                    1.07

     Appearance                          Milky white liquid

     Autoignition Temperature            Not available

     Boiling Point                       100 deg C

     Vapor Density (Air=1)               < 1

     Vapor Pressure, mm Hg @ 20 C        17.5

     Evaporation Rate (Butyl Acetate=1)  < 1

     Upper/Lower Flammable Limits        Not applicable

     Up/Lower Explosive Limits, % by Vol Not applicable

     Flash Point                         Not applicable

     Freezing Point                      0 deg C

     Odor                                Mild acetic aroma

     Odor Threshold, ppm                 Not available

     Solubility in Water                 Dispersible

     Coefficient of Water/Oil Distrib.   Not available



10. Stability and Reactivity

     Normally stable as defined in NFPA 704-12(4-3.1).



	* Conditions to Avoid:

     Exposure to heat, flame and incompatibles.



	* Incompatibilities:

     Strong acids and alkaline materials.



	* Decomposition products may include:

     CO, CO2.



	* Hazardous polymerization:

     Will not occur.



	* Other Hazards:

     None known to Borden.



11. Toxicological Information

     INGESTION:    Not toxic orally when tested as described in 16 CFR Part

                   1500.3 (c)(1) and (2).

     INHALATION:   Not toxic by inhalation when tested as described in 16

                   CFR Part 1500.3 (c)(1) and (2).

     SKIN          Not toxic dermally when tested as described in 16 CFR

     ABSORPTION:   Part 1500.3 (c)(1) and (2).

     SKIN:         Not an irritant when tested as described in 16 CFR Part

                   1500.41.

     EYES:         Not an irritant when tested as described in 16 CFR

                   Part 1500.42.



12. Ecological Information

     Not determined.



13. Disposal Considerations

     Recover free liquid.  Absorb residue and dispose of according to

     local, state/provincial, and federal requirements.



14. Transport Information



14.1 U.S. Department of Transportation (DOT)

     The data provided in this section is for information only and may not

     be specific to your package size.  You will need to apply the

     appropriate regulations to properly classify your shipment for

     transportation.

     Non-Regulated.



14.2 Canadian Transportation of Dangerous Goods (TDG)

     Non-Regulated.



15. Regulatory Information (Selected Regulations)



15.1 U.S. Federal Regulations



	* OSHA Hazard Communication Standard 29CFR1910.1200

     This material is not a "health hazard" or a "physical hazard" as

     determined when reviewed according to the requirements of the

     Occupational Safety and Health Administration 29 CFR Part 1910.1200

     "Hazard Communication" Standard.



	* SARA Title III: Section 311/312

     Does not meet any hazard category



	* SARA Title III Section 313 and 40 CFR Part 372

     This product contains the following toxic chemical(s) subject to the

     reporting requirements of Section 313 of Title III of the Superfund

     Amendments and Reauthorization Act of 1986, and Subpart C-Supplier

     Notification Requirement of 40 CFR Part 372.

     None required per SARA TITLE III SECTION 313.



	* TSCA Section 8(b) Inventory

     All reportable chemical substances are listed on the TSCA Inventory.

     We rely on certifications of compliance from our suppliers for

     chemical substances not manufactured by Borden.



15.2 Canadian Regulations



	* Workplace Hazardous Materials Information System (WHMIS)

     This product has been classified in accordance with the hazard

     criteria of the Controlled Products Regulation (CPR) and the MSDS

     contains all the information required by the CPR.

     Not a controlled product

	* Canadian Environmental Protection Act (CEPA)

     All reportable chemical substances are listed on the Domestic

     Substances List (DSL) or otherwise comply with CEPA new substance

     notification requirements.

	* National Pollutant Release Inventory (NPRI)

     This product contains the following chemical(s) subject to the

     reporting requirements of the Canadian Environmental Protection Act

     (CEPA) subsection 16(1), National Pollutant Release Inventory.

     None required.



16. Other Information

     CP (Non-Toxic):  Products bearing the CP Certified Product 

     Seal of The Art & Creative Materials Institute, Inc.  (ACMI) 

     are certified in a program of toxicological evaluation by a 

     medical expert to contain no materials in sufficient quantities

     to be toxic or injurious to humans or to cause acute or chronic 

     health problems.  This program is reviewed by ACMI's Toxicological 

     Advisory Board.  These products are certified by  ACMI to be labeled 

     in accordance with the chronic hazard labeling standard, ASTM D-4236 

     and Federal law, P.L. 100-695.  In addition, there is no physical 

     hazard as defined within 29 CFR Part 1910.1200(c). Additionally, 

     products bearing the CP Seal meet the specific requirements of material, 

     workmanship, working qualities and color described in the appropriate 

     product standard issued by ACMI or other recognized standards organization.

     MSDS covers items:

     U.S.:    E371, E372, E375, E379, E384, E393, E395, E619, E960, E981

     Canada:  60345, 60352, 60355, 60359, 60375, 60385, 60395



	* User's Responsibility

     The OSHA Hazard Communication Standard 29CFR 1910.1200 and the Workplace

     Hazardous Materials Information System (WHMIS) require that the information

     contained on these sheets be made available to your workers.  Educate and

     train your workers regarding OSHA and WHMIS precautions.  Instruct your

     workers to handle this product properly.  Consult with appropriate experts

     to guard against hazards associated with use of this product and its

     ingredients.



	* Disclaimer

     SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, CONCERNING THE PRODUCT OR THE

     MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE, except that the product

     shall conform to contracted specifications, and that the product does not

     infringe any valid United States or Canadian patent.  No claim of any kind

     shall be greater in amount than the purchase price of the quantity of

     product in respect of which damages are claimed.  In no event shall Seller

     be liable for incidental or consequential damages, whether Buyer's claim is

     based on contract, breach of warranty, negligence or otherwise.



                                                       CUR ISSUE 16-JUN-99

                                                 PREVIOUS ISSUE: 16-JUN-99